Solutions

• Low-Cost monitoring
• Monitor CO, Cl2, h4S, NO2, SO2, O2, NH3, NO, or HCl
• Can monitor, transmit and control
• 4-20 mA or ModBus RTU outputs
• Light industrial or commercial
• Built In Alarm/Buzzer

• Detects O2, CO2, toxic and refrigerant gases
• 4-20 mA output analog transmitter with optional backlit display
• Plug-in and pre-calibrated sensors
• Available with electrochemical, infrared or semi-conductor sensors
• More than 30 different sensors are available to detect most toxic gases in the industry
• Available in an infrared version for CO2
• EN14624 compliant with regards to R134a monitoring

• Loop powered (2-wire) to improve ease of installation
• Common user interface for all toxics sensors to facilitate ease of use and reduce required training
• Compatible with our industry leading Rock Solid sensor technology
• Proven product with large global installed base

• Available in CO2 or h4S versions
• Readily Field Replaceable Sensors
• Simple Operation and Field Calibraton
• Standard Outputs: 4-20 mA, RS-485, 3 Relays
• Non-Hazardous area rated

• 4-20 mA output analog transmitter without display
• Available with catalytic bead, electrochemical or semi-conductor sensors
• Detects combustible, toxic and refrigerant gases (CO, NO, NO2, Methane, Propane, Butane, Hydrogen, LPG, NGV and freons) - EN 14624 compliant with regards to R134a monitoring
• For commercial use (boiler rooms, hospitals, carparks, etc.)
• ATEX 3G certified for use in zone 2 (except semi-conductor version)

• Digital transmitter without display
• Available with catalytic bead or electrochemical sensors
• Detects O2, combustible gas, and toxic gases
• Available for detection of O2, CO2, h4S, NH3, NO, NO2, Methane, Propane, Butane and Hydrogen
• For commercial and light industrial applications (laboratories, cooling rooms, hospitals, boiler rooms, waste water treatment plants, etc.)
• ATEX 3G certified for use in zone 2
• For use only with the MX43 controller

• Detects Explosive and Toxic Gas, or Oxygen
• Non-Intrusive Calibration
• Smart Infrared Gas Sensors
• HART Communication Protocol (NEW)
• MODBUS Communication
• Programmable Relays
• Dual Gas Sensing

(*) versions with local visible alarm are to be installed in ordinary locations only

• Single detector head for all sensor types
• Full range of combustible and toxic sensors
• Supports up to three sensors per transmitter
• Multiple communication protocols
• Global regulatory approvals
• Voted Best Industrial Hygiene - Fixed Permanent System

• Intuitive Non-intrusive Operator Interface
• Modular Plug & Play Sensors & Transmitters
• Simple Menu-driven Calibration & Programming
• Integral Sensor Fault Diagnostics Two Models to Choose From
• Model 500: 4-20mA
• Model 600: 4-20mA, Modbus RTU, Alarm Relays

• XP-intrinsically Safe
• 2 Wire Loop powered
• Field Replaceable Electrochemical Sensor
• Non-intrusive Magnetic Interface
• Built-in Diagnostics
• Fully Encapsulated ITM Electronics
• Quick Thread Release (for sensor replacement)

• 4-20 mA analog transmitter without display
• SIL2 capability for LEL, O2, CO, h4S, NH3, CO2
• Detects combustible, toxic or refrigerant gases and O2
• Available with electrochemical, infrared or semi-conductor sensors
• Designed for industrial applications
• Available in explosion-proof or intrinsically safe versions, and stainless steel
• A high-temperature version allows operation up to 200°C

• Designed for indoor or outdoor monitoring
• Complete reliability
• SIL2 suitable for combustible gases and O2
• Can be fitted on a housing with a M25 or 3/4” NPT thread
• Stainless steel detector provides protection and resistance to corrosive agents
• The precalibrated sensors can be disconnected by turning the head of the unit

• Detection of combustible and toxic gases and O2
• Non-intrusive calibration
• Smart sensors
• HART^® Communication
• Programmable relays
• Hot Swappable sensors (IS Versions)
• 2-wire, 3-wire, ModBus
• Available in stainless steel
• Available in wireless version

• 4-20 mA analog transmitter with display
• SIL2 capability for combustible gases
• Detects O2, combustible, toxic and refrigerant gases
• Corrosion resistant
• Designed for industrial applications
• Available with remote sensor head, flameproof or intrinsic safety versions
• Non-intrusive, one-man calibration
• New XP IR infrared sensor for combustible gases or CO2

• Frequency 2.4 GHz (EU) / 900 MHz (USA)
• Low Power Requirement
• Up to 3 km Line-of-Sight Range
• Robust Mesh Network Topology
• Up to 49 devices per network
• Flexible Input/Output options(analog, on/off, Modbus RS485)

• Water-Proof
• Corrosion-Proof
• Vibration-Proof
• Multi-Layer Surge Protection
• Pre-emptive Fault Diagnostics

• Life-safety performance approved; ATEX & CSA
• 15 year warranty IR sources - solid state optics
• No field recalibration
• Dual skin weather protector – no filters / gauzes or sinters
• Planned maintenance with HART
• SIL 2/3 certified

• Refineries
• Offshore drilling and production platforms
• Processing and storage plants
• Chemical plants.

• Multi-combustible gas detection
• Range of 200 meters
• Low maintenance costs
• Easy detector communication
• Easy configuration and troubleshooting
• Automatic heated optics
• Built-in event recorder
• Stainless steel construction
• Long warranty